The outside is pink, but when you open the lid, the inside and outside are still pink. It's not like brushing a layer on the outside and exposing white on the inside. The board is made of three layers of E-tiles, measuring 1.5 millimeters. When cut open, you can see the three layers of pink face paper, corrugated paper, and pink inner paper. The entire board is die cut, folded up on all four sides, and the tongue is inserted into the slot. Adhesive tape and glue are not needed. The indentation line is clearly pressed, and when folded, follow the line to make the box stand upright. When not in use, lay it flat and stack it up, stuffing a stack under the shelf, saving space in the store. The size is not the same, there are those that fit headphones and coats, and the logo and color can also be changed to yours.
Pink on Both Sides, One Colour Inside and Out
The face of the box is pink, the inside is pink too, the inner sheet is the same colour as the face sheet, and the underside of the lid is pink as well. Open the lid in front of a customer and the inside is not white, there is no place where the colour stops. The pink is on the paper before the box is made, the sheet is printed and then glued onto the flute, so the colour does not come off on a hand the way a coat of ink can. Set it down closed and it reads as a small gift box, not as a parcel.
Three Layer E Flute Board, 1.5 mm Thick
The board is three layers, a pink face sheet, one layer of E flute in the middle, and a pink inner sheet, and the whole board is 1.5 mm thick. Cut a piece in half and the three layers are there to see, the flute runs one way and the two sheets sit on either side of it. The flute runs along the bottom of the box, so the flat surfaces are the ones that take the load, and the box does not give when it is picked up by the sides. The bottom is one whole panel with no join in the middle, and the four sides come up from it in one fold each. The board is thin enough to fold by hand and stiff enough to hold the shape once the tabs are in.
The Cut Edges Are Flat, No Burr Under a Finger
The board is cut by a die in one pass, the edge is straight and it is not torn, and a finger run along it feels no burr. The inside of the box is smooth to the touch, so a piece of jewelry or a folded shirt laid against the wall is not caught on anything. Where the flute is exposed at the edge it is cut clean, no loose paper hangs there.
The Slots Bite Together, No Tape Is Used
The whole box is one sheet, die cut and creased, and it lies flat until it is folded. The two long sides come up, the tabs at the ends go into the slots cut in the panels, and the lid closes over the top with its own tab pressing into the front. No tape and no glue, what holds the box is the slots and the tabs. To open it again the tabs are eased out of the slots, and the box goes back flat without being torn. The crease lines are pressed clear, the fold follows the line and the corners come up at ninety degrees. Flat and stacked when it is not in use, a pile of them takes little room under a shelf, and the shop keeps its floor space.
Sizes Run From One That Holds Earphones to One That Holds a Coat
- A small square one: a necklace in its box, a pair of earrings, one pair of earphones.
- A small flat one: a bracelet, a wallet, a phone case, a small electronic accessory.
- A middle flat one: a folded T shirt, a set of underwear, a thin scarf.
- A middle deep one: kids clothing, a bra, a small gift set with its own box.
- A large flat one: a spring top, a pair of shorts, a thin dress.
- A large deep one: a sweater, a hoodie, a padded jacket, a coat folded once.
- The logo is stamped or screen printed on the lid, and the colour of the board is changed to your own.
A Coloured Face Sheet, How It Is Glued onto the Flute
The pink is printed on the face sheet first, on a roll, and the sheet is printed before it ever meets the flute, which is why the colour is even across a whole run. The printed sheet, the flute and the inner sheet are then glued into one board, and the board is left to sit until the glue holds before it is cut. The board is cut and creased on the die cutting machine in one pass, the cutting and the creasing are lined up on the same die, so the slot and the crease meet where they should. The slots are cut on the same die, and the tab width is set to the board thickness so the tab goes in with a little pressure. On boxes the factory has made mailer boxes, handled boxes, drawer boxes, book style boxes, lid and base boxes, folding cartons, jewelry boxes and flip top gift boxes, on bags it has made paper bags, handled bags, gift bags and wine bags, and hot stamping, logo printing, embossing and UV are all done in the factory.