The mouth of the bag is cut slanting, and one side of the mouth stands higher than the other. The front and the back are cut at the same angle, and the bag reads the same from both sides. A slot is punched in the mouth, and a wide black ribbon comes out of the mouth, so there are two ways to carry. The slot takes one hand, the ribbon takes the whole hand, and the two share the load. The sheet is thick white card, the print is black, and the two sit against each other. The base is folded twice, the bottom is a flat face, and a folded coat rests on it without pulling the body in. The outline, the angle of the mouth and the size are set to your shop, and a new shape starts with a new die. Womenswear shops, streetwear stores and accessory shops hand it over the counter. At a pop up or a fair it stands on the table, and the slant is seen before the print. Our factory cuts the die, folds the body and sets the ribbon in one place, and each bag is opened once before it is packed.
The Slant Sets the Bag Apart on a Shelf
The mouth of the bag is cut on a slant, and one side of the mouth stands higher than the other. The front and the back are cut at the same angle, so the bag looks the same from either side. The mouth line runs down in one pass, and the edge of the mouth is a clean line. The side panel meets the front panel along the slant, and the fold follows the same angle. Standing on a shelf, the bag shows its slant before it shows its print. When your customer walks out with it, the person behind sees the slanted mouth and knows which shop the bag came from, so the bag carries your shop down the street. The slant can be turned to the left or to the right, and the corner can be made rounder, to your order.
The Whole Face Takes Black Print on White
- Bold letters: a heavy store name prints in one pass, the edge of each letter is sharp, and the name is read from across the street.
- Lines and patterns: thin lines and small patterns hold on white card, and they do not fill in.
- Gold stamping and embossing: gold foil and a raised stamp both sit on the white face, and the shape of the bag stays the main line.
- Two colours only: the sheet is white and the print is black, the two sit against each other, and the bag is picked out in a row of bags.
A Slot and a Ribbon Are Two Ways to Hold
A long slot is cut in the mouth, and the cut is rounded at both ends. The slot sits below the mouth line, and the paper left around it is wide enough for four fingers. One hand goes into the slot and lifts the bag, and the other hand is left for a phone or a coat. The ribbon is a wide black webbing, and it comes out of a hole on the left and goes back into a hole on the right. The two ends of the ribbon are fixed on the inside of the mouth, and a glued edge and a stitched line hold them. The ribbon is wider where it meets the hand, so the weight is spread over the palm instead of one line. The ribbon is soft, it bends with the hand, and it does not cut into the fingers after a few blocks. The slot and the ribbon both sit on the same mouth, and the two take the load together. Choosing one does not leave the other loose, and the bag can be carried by the slot today and by the ribbon tomorrow. The ribbon is black and the bag is white, and the two handles read as one line on the front. The height of the ribbon is set to the bag, so the bag hangs below the hand and does not swing against the leg.
A Base Folded Twice Still Stands When Full
The sheet is thick white card, and the bag keeps its shape after it is folded and opened again. The base is folded twice, and the bottom goes in flat, so the bag stands on its own base. A folded coat rests on the bottom face, and the body does not pull in at the sides. Small items such as a jewelry box or a pair of earrings sit on the base, and the paper around them stays up. In the shop the bag stands on a shelf with the slant facing out, and it does not need anything behind it. The mouth keeps its line when the bag is full, and the slot does not pull out of shape. A bag that is carried every day still opens wide at the counter, and the base is still flat.
Womenswear and Street Shops Carry It Out
- In a womenswear shop: a dress on its hanger goes in, and the top of the dress stays under the slant.
- In a streetwear store: a folded hoodie and a cap go in.
- In an accessory shop: a few small boxes of earrings and rings go in.
- In a boutique: a coat and a pair of shoes go in, one on each side.
- For a holiday gift: a scarf and a card go in.
- At a pop up: the bags stand at the entrance, and a customer picks one up on the way out.
An Odd Shape Starts With a Cutting Die
An odd shape starts with a cutting die, and the die is cut to the outline you send. A new outline, a steeper slant or a rounder corner all go into the die first. The sheet is cut on the die in one pass, and the mouth, the corner and the slot come out together. The cut pieces go to the folding table, the sides are glued, the base is folded, and the ribbon is set into the mouth. The first bag off the die is opened and checked, and it is put against the drawing before the rest are run. Each bag after that is opened once, and the mouth line, the slot and the two ends of the ribbon are looked at. Our factory cuts the die in house, so a new outline does not wait on an outside tool shop.