The lid carries an emboss pressed into the paper, and the gold logo sits on the same face. Under the fingers the pattern goes up and down, and from the side the light shows the depth. The lid is a full cover, it goes down over the base and stops where the two edges meet. The body is built on thick grey board, and the corners are taped before the art paper goes on. A tray can be fitted inside, cut to the article that goes in. The ribbon carries your name, it is tied into a bow, and the box leaves as a gift. Two boxes stacked, the lid of the lower one takes the base of the upper one, and the sides stay straight. A dress, a scarf and a set of skincare each go into a box of this kind. Our factory presses the relief, foils the logo and fits the tray in one place, and each lid is tried on its base before packing. The size, the depth of the emboss and the inside of the box are set to your order.
Lid and Base Gift Box
The lid is a full cover, and it goes over the base on all four sides. The lid goes down and stops where its edge meets the base edge, and the joint is one line. The lid and the base are cut from the same sheet of board, so the gap is the same all round. The lid lifts with two fingers at the corner, and it comes off without a pull. The lid is put back on after a look, and it goes down the same way every time.
The Emboss on the Lid Is Felt Layer by Layer
The lid carries an emboss, and the pattern is pressed into the paper, not printed on top. The paper is art paper with some tooth, and the pattern rises out of it. The press goes over the same spot twice for a deeper relief, and the tallest point of the pattern stands above the flat face. A finger run across the lid finds the leaves and the lines, and the light from the side shows the depth. Around the emboss the logo is foiled in gold, and the gold sits on a flat area so the two do not fight. The gold is a foil pressed at a set heat, and the edge of each letter is cut clean. The pattern is drawn to the size of your lid, so a small box gets a pattern with fewer lines. A deep relief needs a thicker paper, and the paper is chosen with the depth. On a shelf the lid is read from an angle, and the relief throws a shadow along the pattern.
The Grey Board Stands Up and Stacks Without Leaning
The body is built on thick grey board, and the board is the wall, not a lining. The corners are taped on the inside, and the tape holds the two walls at a right angle. The art paper is glued over the board and turned into the inside, so no board edge shows. The box stands on its own four walls, and it does not lean when it is put down. In an outer carton the box has a gap on each side, and it does not touch the carton wall. The box travels lid on base, and the lid stays where it was set. On a display table the box can be stood on end or laid flat, and it reads the same from both. A box opened at the counter is closed again and put back on the shelf.
The Print the Colour the Ribbon and the Tray Can All Be Changed
- Print: the pattern is drawn to your lid, and a name, a line of text or a mark all go on the same face.
- Colour: the art paper comes in white, cream, grey, and a colour matched to your sample.
- Ribbon: the ribbon is printed with your name, and it is tied in a bow, once or twice round the box.
- Tray: the inside is cut to what goes in, with a bed for a bottle or a slot for a card.
- Size: length, width and depth are set to the article, and the depth follows the height of the box.
The Ribbon Is Tied and the Box Goes Out as a Gift
- In a clothing shop: a folded dress and a belt go in, and the box is handed over tied.
- For a wedding: the dress box goes to the couple with the ribbon still on.
- For a skincare set: a bottle and a jar sit in the tray, and the box goes out as it is.
- For a business gift: a pen and a card go in, and the box needs no bag.
- At a hotel or an event: a set of small gifts goes in, and the boxes are lined up on the table.
- At a pop up: the box is put on the counter and taken away without wrapping.
From the Drawing to the Carton It Is All Done in One Place
Our factory works from one drawing, and the drawing carries the size, the artwork and the depth of the box. The box is made in one place: the board is cut, the corners are taped, the art paper is glued on, the emboss is pressed, the gold goes on, and the tray is fitted. One person follows your order from the drawing to the carton, so a change of size or colour comes back from the same person. When the order repeats, the box follows the same size and the same layout, and the second batch lines up with the first. The die and the cutting layout are kept with the order number, so nothing has to be drawn again. The boxes are packed in an outer carton with a gap on each side, and the carton is marked with the size and the count. Every lid is tried on its base before it is packed, and a lid that sits high is put aside.